Let
In this paper, we derive a time-consistent solution for mean-variance portfolio selection within the framework of the HN-GARCH model. Then, by using the optimal solution derived under exponential utility as a reference point, we introduce a well-defined performance metric, namely certainty equivalent return loss (CErL), to assess portfolio performance. Finally, based on the historical data of the NASDAQ-100 Index, Monte Carlo simulations empirically demonstrate that the solution under the HN-GARCH model outperforms that under a homoscedastic variant in terms of CErL and the performance of asymmetric HN-GARCH is better than symmetric HN-GARCH’s performance.
In this paper we compute the higher order long time asymptotics of the linear Schrödinger equation using the
As the demand for drag-free control missions, such as space-based gravitational wave detection, grows, so does the need for high-precision, low-noise micro-thrust measurements. A significant challenge in ground-based micro-thrust measurements is the error caused by coupling with microgravity. To overcome this, we propose a cascaded torsion pendulum system for accurate ground-based micro-thrust measurements. A dual torsion pendulum model with coaxial transmission was developed to analyse the effect of centre of mass offset and baseline tilt on measurement accuracy, facilitating the decoupling of gravitational noise from thrust measurements. Multi-body simulations were performed using Simscape, followed by cascaded pendulum experiments to investigate the dynamic response of the system under different conditions. The experiments confirmed the effectiveness of the method in minimising noise. The results demonstrate that the cascaded pendulum system can successfully decouple gravity-induced disturbances in a low-frequency vibration environment (~1 mHz), enabling accurate thrust measurements at the micro-Newton level. This approach provides a reliable method for evaluating the performance of micro-thrusters in space-based gravitational wave detection missions.
This work investigates the flow of liquid metals around a near-wall cylinder and the enhancement of heat transfer under a magnetic field through numerical simulations. It analyzes the physical mechanisms of influence of the magnetic field, the amplitude of the vibrating plate, the heat flux and gap ratio(G/D) on flow structure and heat transfer. The results indicate that the Lorentz force drives the vortex toward the heated plate. As the magnetic field increases, the vortex shedding behind the cylinder exhibits a trend of first being promoted and then suppressed, resulting in a non-monotonic variation in heat transfer efficiency, which first increases and then decreases. Increasing the amplitude of the heated plate enhances the velocity disturbance between the cylinder and the plate, which reduces the thickness of the temperature boundary layer, thereby significantly improving the heat transfer. The changes in heat flux and gap ratio significantly impact the flow structures and the vortex shedding modes. When G/D increases, the heat transfer efficiency shows a trend of first increasing and then decreasing due to the interaction between the heated plate and the vortices.
The structure of microbial communities and the distribution of antibiotic resistance genes (ARGs) in hospital environments may have potential impacts on early life. This study collected 35 dust samples from the obstetrics outpatient environment of a tertiary hospital in Beijing and analyzed the microbial communities and ARGs using metagenomic sequencing technology. The analysis revealed 17 microbial phyla in the samples, among which Actinobacteria, Proteobacteria, and Firmicutes emerged as the dominant groups, with their cumulative relative abundance reaching 97.66%. Significant differences in microbial presence were observed among various locations, with higher diversity found in high-contact areas. A total of 182 ARGs, conferring resistance to 91 antibiotic types, were identified, with the cumulative abundance of vancomycin and tetracycline classes reaching 44.95%. Through binning, a total of 111 types of bacteria corresponding to ARG hosts were identified, among which Cutibacterium acnes and Kocuria rosea are the main contributors. This study provides important data for understanding the distribution of microbial communities and ARGs in the hospital maternity outpatient environment and may offer a scientific basis for infection prevention and control strategies in hospitals.
The Qin Dynasty was the first unified centralized kingdom in Chinese history. To answer how the Qin people became prosperous after their migration to the Guanzhong area, a detailed investigation of their subsistence strategy is necessary. Pottery was the major container for ancestor to cook, serve, and preserve food. The lipid analysis of pottery sherds represents a novel approach to investigating this issue. In this study, lipid extraction and analysis were performed on 45 potsherds from the Matengkong site of Xi’an City. The results showed that the pottery was used for the processing of non-ruminant animals which fed on C3 plants and probably were wild animals. In addition, plant resources, including broomcorn millet, were also important in ancestors’ diets. According to the historical documents, under the strict hierarchy of Zhou Dynasty, commoners were prohibited from consuming large livestock such as pigs, cattle, and sheep. Instead, wild animals obtained from hunting constituted a certain source of meat for commoners. The superior natural environment and abundant natural resources of the Guanzhong area provided the foundation for this practice.
In traditional geological fieldwork, data collection primarily relies on manual on-site measurements, which are labor-intensive and inconvenient for data analysis. Moreover, such methods are not feasible for steep and inaccessible areas, presenting numerous limitations. To address these challenges, this study employs two advanced techniques: unmanned aerial vehicle (UAV) oblique photogrammetry and airborne LiDAR scanning, to reconstruct three-dimensional (3D) geological models and conduct data measurements via computer analysis. The study focuses on the Longmen formation fluvial facies strata in the Yanqi Lake area of Beijing. Within the model, the stratigraphic profile is divided into nine lithological units, with each layer subjected to measurements of thickness and orientation. Additionally, geological phenomena such as faults and structural deformations are identified. The model undergoes spatial coordinate verification and accuracy validation, revealing measurement errors of less than 0.01 m in length and less than 2° in orientation. Through comprehensive profile measurements and the characterization and identification afforded by the 3D model, it is concluded that the profile exhibits multiple braided river depositional sequences in the vertical dimension. These sequences consist of lower channel lag deposits, middle channel bar deposits, and upper floodplain aggradation deposits. Consequently, compared to traditional geological data collection methods, the use of UAV-based 3D geological models not only meets quality and precision standards but also enhances operational efficiency and reduces the risks associated with fieldwork.
Mountainous highways are often threatened by rockfalls detached from high and steep slopes, while the steep terrain makes it difficult to obtain the information of discontinuities and to precisely identify the dangerous rock mass. The reliability of risk assessment of the dangerous rock mass and the effectiveness of its prevention and control are thus seriously affected. Therefore, taking the dangerous rock mass on Heiduo high-steep highway slope, Diebu County, Gansu Province as the research object, the paper utilized unmanned aerial vehicle (UAV) photogrammetry technology to obtain the 3D point cloud data of the slope, and used the k-nearest neighbor algorithm and least squares method to automatically identify and obtain the occurrence information of the slope discontinuities, manually interpreted and identified the potential unstable rock masses and qualitatively analyzed their stability, and finally applied the RocPro3D software to simulate and analyze the kinematic characteristics of the unstable rock masses after failure. The results show that: 1) The slope structure and high-steep terrain are the basic geological conditions for the development of rockfalls on the Heiduo highway slope. 2) Six groups of predominant discontinuities including bedding were automatically identified, and 6 dangerous rock masses were interpreted, of which 5 were determined to be unstable; 3) The rockfalls sourced from the 5 dangerous rock masses could move onto the highway, among which the WYT4 has the widest impact scope, and the movement distance of the blocks under the predominant path could reach as far as 619 m, indicating that it is the most dangerous one. 4) The spatial distribution data of blocks of previous rockfalls can be used to effectively and reliably invert the kinematic parameters of potentially dangerous blocks. The results can provide basic theoretical guidance for the design of rockfall prevention and control of dangerous blocks on the high-steep slope, and the research method can provide a useful reference for the identification of the discontinuity of the dangerous rock mass and for the risk assessment of rockfall on similar high-steep slopes.
Cross-view image geo-localization (CVGL) is a key technique for achieving geographic location matching through multi-source images, with broad applications in fields such as robotic navigation and autonomous driving. However, existing methods typically assume that images are directionally aligned, making them less effective in real-world scenarios with directional deviations. To address this challenge, this paper proposes a ranking aggregation-based method for enhancing directional robustness. By introducing random directional shifts to ground-level images and employing mean and minimum aggregation strategies, the proposed method improves the matching accuracy and robustness. Experiments conducted on the CVUSA_360 and CVACT_360 datasets demonstrate that this approach significantly enhances the performance of various models under directionally misaligned conditions, with particularly outstanding results in terms of the R@1 metric. Visual analysis further verifies the advantages of the method in strengthening directional robustness, suppressing noise, and improving matching accuracy, thus providing an efficient solution for geo-localization tasks in complex scenarios.
To address the contradiction between computational efficiency, imaging quality, and azimuth bandwidth in existing algorithms, this paper proposes an adaptive and efficient sliding-spotlight SAR imaging method based on chirp scaling. Sliding-spotlight SAR, as an important imaging mode, combines the advantages of high resolution and wide azimuth bandwidth. However, current methods face the problem of high computational complexity when dealing with wide azimuth bandwidths, and severe range-azimuth coupling issues under large squint angles. Therefore, this paper introduces a chirp scaling processing mechanism based on the traditional two-step imaging algorithm and combines range walk correction techniques to effectively solve the severe range-azimuth coupling problem in squint sliding-spotlight mode, significantly improving imaging efficiency. Experimental results show that the proposed method achieves good imaging results in both side-looking and squint sliding-spotlight modes and demonstrates higher computational efficiency under wide bandwidth conditions. Additionally, by comparing the imaging performance under different azimuth bandwidths in squint conditions, the adaptability of the proposed method under wide bandwidth conditions is verified, providing an effective solution for wide-swath imaging at large squint angles.
This paper proposes a fault data generation method for satellite turntables based on a diffusion model and the Informer architecture, to address the issue of limited fault data samples in satellite telemetry, which restricts the performance of fault detection and diagnosis models. By integrating time series decomposition with deep learning models, the proposed method aims to generate high quality and interpretable time series data. Through data decomposition, the forward diffusion process achieves component decoupling, improving the diversity and accuracy of the generated data. During the reverse generation phase, the Informer decoder leverages a sparse self-attention mechanism to effectively capture long-term dependencies and complex temporal patterns. The method is suitable for both unconditional and conditional fault data generation, including scenarios with missing data. Experimental results demonstrate that the proposed method significantly outperforms generative adversarial networks and variational autoencoders in terms of metrics such as mean squared error, correlation score, and correlation coefficient.
Precisely perceiving the future actions of surrounding traffic agents is critical for ensuring the safety of autonomous vehicle. This paper mainly focuses on the complicated problem of long-term multi-agent trajectory prediction. Existing trajectory prediction methods can be categorized into joint prediction and marginal prediction. Although joint prediction methods achieve better scene consistency in multi-agent scenarios, both of them fail to reach satisfactory results in long-term prediction tasks due to their inability to capture changes in driver behavior over time. In this paper, we introduce a novel joint prediction method called trajectory prediction through post-processing (TPP). The core of this method is the trajectory post-processing module, which utilizes attention mechanisms to model interactions among different vehicles. By representing a single vehicle with multiple embeddings, the module also simulates the changes in behavior during driving. With the help of a post-processing module, our method is able to generate consistent multi-agent trajectories. We evaluate TPP on a short-term prediction dataset and a long-term prediction dataset separately, comparing it with mainstream trajectory prediction methods. The results indicate that TPP achieves better performance.
The interplanetary scintillation(IPS) monitor receives time varying signal from radio sources through multiple stations correlation. It observes the flux of the radio sources through solar wind and coronal mass ejections from a large view angle in multiple perspectives, and the density and velocity of the interplanetary solar wind could be calculated through the observed data. The dynamic phenomena also track the position and range of the interplanetary coronal mass ejections. The main station of this monitor has three movable parabolic cylindrical antennas, each one is 140 meters long from north to south and 40 meters wide from east to west. The antenna pattern and the panel deformation values of the parabolic cylindrical antenna at different elevation angles and ambient temperatures are simulated and calculated. The variance of the gain is ±0.5 dB between deformation and without deformation, which verifies the feasibility of the design.